Showing results: 586 - 600 of 627 items found.
-
NMR-EA300 System -
Caylar
The NMR-EA300 system is the reference for calibrating magnetic sensors. It allows to generate an absolute magnetic field at <±10mG (0.1 uT) without temperature drift (<0.1ppm/C°) over a range from 14mT to 3T. This system is composed of an EA300 electromagnet with NMR poles, a MPU-16U ±150A ±70V current source of class 1ppm and a NMR20 Teslameter with a magnetic field controller (FR020).A thermostat chamber can be installed in the air gap (Optionally available on 50mm and 70mm gap poles).
-
NI
The C Series Universal Analog Input Module helps you perform multi-purpose measurements. This module includes built-in support for accelerometer, powered sensor, full-bridge, and voltage measurements as well as quarter-bridge, half-bridge, 60 V, and current measurements using measurement-specific adapters. You also can choose options to measure signals from sensors such as strain gages, resistance temperature detectors (RTDs), thermocouples, load cells, and other powered sensors.The C Series Universal Analog Input Module includes the NI-DAQmx driver and configuration utility that simplify configuration and measurements. NI-DAQmx supports NI programming environments as well as Python, ANSI C, C#.NET, and MathWorks MATLAB® software.
-
ARO-PR -
JFE Advantech Co., Ltd.
The Portable optical DO meter makes use of the fast-response optical DO sensor RINKO, maintaining its high-speed response performance (99% response < 7sec). The meter probe is equipped with a temperature sensor close to the sensing foil, and the measurements are made by simply inserting the probe into a DO sample bottle (the calibration is carried out using the National Metrology Institute of Japan (NMIJ) certified traceable gases standards). Differently from galvanic electrode sensors, the instrument does not require water sample stirring or fixing reagents, since there is no oxygen consumption. Thus, the required time to estimate dissolved oxygen is considerably reduced. The display unit shows the output instantaneously, and you can check the measured values in real time.
-
ADLINK Technology Inc.
ADLINK remote IO and serial communication cards are suitable for handling multiple digital signal types for IoT and other industrial applications such as facility monitoring, environmental monitoring, and industrial process control.Remote IO - NuDAM modules provide direct communication with various sensors, including performing signal conditioning, scaling, linearization and conversion to obtain temperature, pressure, flow, voltage, and current measurements. The new ND6100 series modules use Modbus/RTU remote data transmission protocols, providing customers with a comprehensive product portfolio. ADLINK's serial communication cards provide a PCI/PCIe interface and support RS-232 and CAN communication interfaces, allowing customers to choose the most suitable communication card for various automation equipment needs.
-
AAQ-RINKO -
JFE Advantech Co., Ltd.
The water quality profiler, AAQ 1183 has been redesigned as AAQ-RINKO with an optical fast response (63% response in water, 0.4 s) DO sensor, RINKO. Conventional water quality profilers with a slow response DO sensor require holding the instrument for a certain period at the measurement depths. AAQ-RINKO makes vertical measurements possible with a profiling speed of 0.5 m/s, similar to CTD observation, thereby significantly reducing the observation time. In addition to conductivity, temperature, depth, chlorophyll, turbidity, DO and pH, AAQ-RINKO also enables simultaneous installation of PAR (Photosynthetic Available Radiation) and ORP (Oxidation Reduction Potential) sensors. The processing unit is available in three types in accordance with the observation applications.
-
Extech 45170CM -
Extech Instruments Corporation
The 45170CM is a convenient 5-in-1 Environmental Meter which measures Air Velocity, Air Volume, Humidity, Temperature and Light. Ergonomic housing design with a large dual "smart" LCD where characters on display reverse direction depending on the function in use. This multi-functional meter is ideal for professional or home use in testing the environmental quality in a building. Featuring Data Hold, Min/Max, Auto Power Off functions. Complete with built-in sensors, wrist strap and 9V battery.
-
imec
Imec is a reference in the design of ultra-low power electronics, low-power algorithms to increase intelligence and data security, and in all aspects of data science. Our multi-sensor environmental monitoring platform features sensors for temperature, relative humidity, NO2, CO2, VOC (volatile organic compounds), particle matter, ambient light, sound, vibrations and presence detection. Our test platform is suitable for indoor and outdoor air quality monitoring and control, and can be used in smart buildings, smart cities and more.
-
THERMES-USB RF -
Physitemp Instruments
Physitemp’s original Thermes high accuracy ISA based data acquisition system has been redesigned to create a more versatile USB model. The new system requires no internal connections to your computer and simply connects via an external USB port on your laptop or desktop computer. Two versions of the data acquisition system are available. The standard version, THERMES USB, is connected to your computer USB port. The wireless version - THERMES USB WFI, can be either directly connected to a USB port or, with the included wireless receiver, positioned up to 100 feet from the host computer. Each unit will accommodate up to 7 type T thermocouple sensors and multiple Thermes units may be connected to the same computer for more thermocouple inputs. A high accuracy electronic cold junction compensation circuit maintains typical system accuracy of ±0.2°C over an ambient temperature range of 15 to 35°C. Individual offsets may be added to each input in software to facilitate individual calibration of each channel. For information on our wide selection of Type T Thermocouple temperature probes.
-
AML -
OAI
Wafer bonding has found many applications in the field of MST, MEMS and micro engineering. These include the fabrication of pressure sensors, accelerometers, micro-pumps and other fluid handling devices. The process is also used for first-order packaging of silicon microstructures to isolate package-induced stresses. The OAI AML Wafer Bonder facilitates both the alignment and bonding to be performed in-situ, in a high vacuum chamber. For anodic bonding the wafers are loaded cold and heated in the process chamber. For high accuracy alignment the wafers are aligned and brought into contact only after the process temperature has been reached, thus avoiding differential thermal expansion effects which can compromise alignment. The AML Wafer Bonder is excellent for anodic bonding, silicon direct and thermal compression bonding applications. These features enable the bonder to be used with virtually any processing tool.
-
HiRES -
HIGHVOLT Prüftechnik Dresden GmbH
The digital recorders HiRES are used to measure, store, and evaluate signals from up to 64 sources synchronously. Depending on the sensors used voltages, currents, temperatures, mechanical movements and various other signals can be measured. This measurement system features the ability to capture fast transient processes such as those occurring in impulse current tests on electrical devices or during switchgear testing. The system is also capable of measuring semistationary and periodic events such as DC voltage and AC voltage as well as superimposed semistationary, periodic and transient processes.
-
Analog Devices Inc.
Analog Devices’ comprehensive portfolio of integrated monitoring and control components combine ADCs, DACs, temperature sensors, GPIOs, and current sensing technologies in a wide range of configurations. ADI integrated solutions save space over discrete implementations and simplify operations and provide the configurability your system requires. These products are ideal for general system monitoring of peripherals like power supplies or system voltages and currents. Used in wireless base stations, optical transceivers, transponders, and industrial systems such as building control, these converters offer versatility and flexibility.
-
General Tools & Instruments
General offers weather detection systems that use a base station to display inputs received wirelessly from remote sensors. The RGR150 can track rainfall amounts as well as temperature and/or relative humidity. WS821 & WS831DL Weather Detection Systems are full-featured wireless weather stations that add wind speed readings and track trends in barometric pressure that can serve as the basis of a short-term weather forecast. Barometric pressure is also available from a dedicated wireless station (the DBAR880), and the original weather forecasterthe ABAR300 Analog Barometer.
-
Curtiss-Wright Defense Solutions
Our PC104 switches provide systems integrators with a fast and powerful way to interconnect chassis, cards, and CPUs through switched Fast and Gigabit Ethernet links. These PC/104 Ethernet switches, optimized for size, weight, and power (SWaP)-sensitive embedded military and civilian computer network systems applications, enable reliable local area network (LAN) switching in extended operating temperature ranges and extreme shock/vibration environments. Ideal for connecting computers, cameras, sensors, and command and control equipment, these cards are typically deployed in manned and unmanned system platforms.
-
Environment Associates Inc.
We service most industry segments with harsh environment, salt fog corrosion testing.If your product is coated or painted for the marine, automotive or military industries, we are equipped to provide accredited testing within multiple chambers.We provide ASTM sample preparation for coated and painted articles to ensure that your test is performed correctly.We also provide custom configurations with varied salt concentrations and temperatures for many customers with products that are used in unique environments. Products like circuit boards, electronic devices and sensors may all have specialized testing requirements.
-
WIKA Alexander Wiegand SE & Co. KG
In-line ultrasonic flow meters provide accurate gas flow measurement by calculating the transit time difference ratios between ultrasonic paths into a pipe. WIKA ultrasonic flow meters are intrinsically safe (ATEX/IECEx) and approved for custody transfer (MID 2014/32/EU, OIML R137). These solutions ensure low power consumption and easy and quick installation and commissioning, and are suitable even in the most demanding applications. Sound velocity, signal-to-noise ratio and other additional measured variables are available for condition monitoring, as well as connectable pressure and temperature sensors for achieving integrated volume conversion.
